Roofing Contractors in San Antonio, TX

Ask if they are a member of any regional or nationwide trade companies.

A number of resources are readily available to discover a qualified roofing contractor; recommendations, local government licensing agencies, and web sites that provide professionals for hire, or a list of contractors who are certified and bonded.

A licensed roofing contractor can be called to prevent more damage to the roofing, or individual injury to the property owner caused by attempting to check it his or her self. A roof inspection must be performed every year; consistent weathering by sun, heat, rain, snow, cold, wind, and hail can cause roof material to break down. A licensed roof contractor will know what to look for.

Ask possible roof contractors concerns such as whether or not they are certified and bonded.

Call 888-479-8303 Now!

Our roofing contractors can provide Roof Leak Repairs. If you have any questions or concerns about our service area, please give us a call today. We are competitively priced in this area from other roofing companies because we are confident that you will be thrilled with how your roofing project will turn out. Again, call today to schedule a estimate for your roofing project.

Roofers in Bexar County

How to do Metal Roof

Thought of installing metal roof yourself? Do not even trouble to think of it. Putting on new metal roofing and even doing repair work is not as easy as you thought it is. Learning how to do metal roof is a complex one. It entails several procedures, special techniques and would need using quite a variety of assorted metal tools and accessories. Metal roofing is mainly done by expert installers, as this is not merely a do-it-yourself job. It is wise to work with an experienced roof expert to install a moderate to intricate metal roof. Let us have a quick learning of the procedures and the needed requirements on how to do metal roofing.

The extremely initial step on how to do metal roofing is to understand just how much metal roofing is needed and this will be figured out by measuring the height and length of the roofing system and its edges. It is essential to do careful evaluation of loose roof or harmed protrusions if you are up for a modification of your old roof. Check the roofing system pitch utilizing a determining square and a level and remember of the minimum requirement as recommended by the producer.

The next requirement is to determine the roofing underlayment which helps avoid unneeded moisture on the metal roof throughout certain weather conditions. The underlayment should protrude on all roof edges by 1 1/2 inches, expand on vent pipes by at least 1 1/2 inches, and on sidewalls by at least 6 inches. It is best to put on red rosin paper over the felt paper to avoid sticking on the metal if your metal roofing system is located right against the underlayment.

The next couple of steps on how to do metal roof will deal more with the metal sheets. Screw the metal roof into the wood slats with the usage of 1/4 inch metal wood screws every 2 feet on both sides. Attach the metal sheets by putting in 5/16 inch lap screws every four feet where 2 sheets overlap each other.

Start working on the sides of the roof with the metal trim to cover its edges as well as the roofing system ridge which need to be bent over to fully cover it. Use 1/4 inch metal wood screws for the metal trim.

These are just the fundamental treatments on how to do metal roof. whole procedure is much more complicated if you care to ask an expert. If you wish to attempt the roofing work on your garage, for instance, simply make sure to carefully follow the steps and utilize the appropriate working tools.

The extremely first action on how to do metal roof is to know how much metal roofing is required and this will be determined by measuring the height and length of the roof and its edges. If your metal roofing system is situated right against the underlayment, it is best to put on red rosin paper over the felt paper to avoid sticking on the metal.

The next couple of actions on how to do metal roof will deal more with the metal sheets. Screw the metal roofing into the wood slats with the usage of 1/4 inch metal wood screws every 2 feet on both sides. Use 1/4 inch metal wood screws for the metal trim.

Show Less